1 : 22ms GET DEVICE DESCRIPTOR
Release = 2.0.0 Version of the USB protocol.
Class = 0xff Class is vendor specific.
Subclass = 0xff Subclass is vendor specific.
Protocol = 0xff Protocol is vendor specific.
Maxpacket = 64 Maximum Packet Size for endpoint0 (the control endpoint).
Vendor = 0x04a9 The product vendor: Canon
Product = 0x2214 The product model:
Devrelease = 3.0.2 Release number of this device.
Imanuf = 0x01 Index to string describing the manufacturer.
Iproduct = 0x02 Index to string describing the product.
Iserial = 0x00 Index to string describing the device's serial number.
Numconf = 0x01 Number of configurations for this device.
2 : 22ms GET CONFIG DESCRIPTOR
Totalength = 39 Total bytes returned for this configuration, its interfaces and endpoints.
NumIntf = 0x01 Number of interfaces supported by this configuration.
ConfigVal = 0x01 Value to use to select this configuration.
Iconfig = 0x00 Index to string describing this configuration.
Attrib = 0xa0 Attributes: Remote_wakeup
MaxPwr = 500mA Maximum operational power required by this device.
3 : 23ms GET CONFIG DESCRIPTOR
Totalength = 39 Total bytes returned for this configuration, its interfaces and endpoints.
NumIntf = 0x01 Number of interfaces supported by this configuration.
ConfigVal = 0x01 Value to use to select this configuration.
Iconfig = 0x00 Index to string describing this configuration.
Attrib = 0xa0 Attributes: Remote_wakeup
MaxPwr = 500mA Maximum operational power required by this device.
GET INTFCE DESCRIPTOR
IntfNum = 0x00 Number of this interface.
AltSet = 0x00 Value used to select alternative setting for this interface.
NumEndp = 0x03 Number of end points supported by this interface (excluding control endpoint).
Iclass = 0xff Class is vendor specific.
Isubclass = 0xff Subclass is vendor specific.
Iprotocol = 0xff Protocol is vendor specific.
Iindex = 0x00 Index to string describing this interface.
GET ENDPNT DESCRIPTOR
EndpAddr = 0x81 Endpoint Address: number=1 direction=read
Attrib = 0x02 Attributes: Transfer=bulk Synch=no syncronisation Usage=data
Maxpacket = 512 Maximum Packet Size for endpoint.
Interval = 0x00 Polling interval for this endpoint.
GET ENDPNT DESCRIPTOR
EndpAddr = 0x02 Endpoint Address: number=2 direction=write
Attrib = 0x02 Attributes: Transfer=bulk Synch=no syncronisation Usage=data
Maxpacket = 512 Maximum Packet Size for endpoint.
Interval = 0x00 Polling interval for this endpoint.
GET ENDPNT DESCRIPTOR
EndpAddr = 0x83 Endpoint Address: number=3 direction=read
Attrib = 0x03 Attributes: Transfer=interrupt Synch=no syncronisation Usage=data
Maxpacket = 1 Maximum Packet Size for endpoint.
Interval = 0x08 Polling interval for this endpoint.
4 : 98ms SELECT CONFIGURATION See raw log for details
5 : 121ms READ SOMETHING??? 0
6- 7: 122ms [gl841:scanner_status] -> 0x50 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
*scanning is : finished
motor feeding : not finished
*image buffer is : empty
power : off
8- 9: 133ms [gl841:scanner_status] -> 0x50 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : off
10- 11: 134ms [gl841:motor_gpio17_18] -> 0x00 Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 0
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
12 : 135ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
13 : 136ms UNKNOWN URB
14 : 137ms UNKNOWN URB
15- 16: 138ms [gl841:motor_gpio17_18] -> 0x0c Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 0
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
17 : 139ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
18 : 139ms UNKNOWN URB
19 : 140ms UNKNOWN URB
20 : 141ms Wrote an address 0x06 in preparation for a bulk read/write from/to the GL841.
21 : 142ms UNKNOWN URB
22 : 142ms UNKNOWN URB
23 : 143ms Wrote an address 0x6e in preparation for a bulk read/write from/to the GL841.
24 : 143ms UNKNOWN URB
25 : 144ms UNKNOWN URB
26 : 145ms Wrote an address 0x6f in preparation for a bulk read/write from/to the GL841.
27 : 146ms UNKNOWN URB
28 : 146ms UNKNOWN URB
29- 30: 147ms [gl841:motor_gpio17_18] -> 0x0c Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 0
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
31 : 148ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
32 : 149ms UNKNOWN URB
33 : 249ms UNKNOWN URB
34- 35: 249ms [gl841:gpio16_9_data] -> 0x00 Read state of GPIO pins 16 to 9.
gpio9 : 0
gpio10: 0
gpio11: 0
gpio12: 0
gpio13: 0
gpio14: 0
gpio15: 0
gpio16: 0
36 : 250ms Wrote an address 0x6c in preparation for a bulk read/write from/to the GL841.
37 : 250ms UNKNOWN URB
38 : 261ms UNKNOWN URB
39- 40: 261ms [gl841:gpio8_1_data] -> 0x0f Read state of GPIO pins 8 to 1.
*gpio9 : 1
*gpio10: 1
*gpio11: 1
*gpio12: 1
gpio13: 0
gpio14: 0
gpio15: 0
gpio16: 0
41 : 262ms Wrote an address 0x6d in preparation for a bulk read/write from/to the GL841.
42 : 262ms UNKNOWN URB
43 : 361ms UNKNOWN URB
44- 45: 361ms [gl841:motor_gpio17_18] -> 0x0e Read Set motor pins and GPIO17-18.
GPO17 : 0
*GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
46 : 362ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
47 : 363ms UNKNOWN URB
48 : 363ms UNKNOWN URB
49- 50: 364ms [gl841:motor_gpio17_18] -> 0x0e Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
51 : 365ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
52 : 365ms UNKNOWN URB
53 : 365ms UNKNOWN URB
54- 55: 366ms [gl841:motor_gpio17_18] -> 0x0e Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
56 : 367ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
57 : 367ms UNKNOWN URB
58 : 387ms UNKNOWN URB
59- 60: 388ms [gl841:motor_gpio17_18] -> 0x0a Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
61 : 389ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
62 : 389ms UNKNOWN URB
63 : 409ms UNKNOWN URB
64- 65: 410ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
66 : 411ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
67 : 411ms UNKNOWN URB
68 : 412ms UNKNOWN URB
69 : 412ms WRITE SOMETHING??? (index=0x10) 148
70 : 432ms UNKNOWN URB
71 : 433ms UNKNOWN URB
72 : 434ms UNKNOWN URB
73 : 435ms UNKNOWN URB
74 : 455ms UNKNOWN URB
75 : 456ms Wrote an address 0x10 in preparation for a bulk read/write from/to the GL841.
76 : 456ms UNKNOWN URB
77 : 457ms UNKNOWN URB
78 : 457ms [gl841:expr] -> 0x0600 Read exposure time for red channel (1536) from the GL841.
80 : 458ms Wrote an address 0x11 in preparation for a bulk read/write from/to the GL841.
81 : 459ms UNKNOWN URB
82 : 459ms UNKNOWN URB
83 : 460ms [gl841:expr] -> 0x0013 Read exposure time for red channel (19) from the GL841.
85 : 460ms Wrote an address 0x12 in preparation for a bulk read/write from/to the GL841.
86 : 461ms UNKNOWN URB
87 : 461ms UNKNOWN URB
88 : 462ms [gl841:expg] -> 0x5500 Read exposure time for green channel (21760) from the GL841.
90 : 463ms Wrote an address 0x13 in preparation for a bulk read/write from/to the GL841.
91 : 463ms UNKNOWN URB
92 : 464ms UNKNOWN URB
93 : 464ms [gl841:expg] -> 0x0002 Read exposure time for green channel (2) from the GL841.
95 : 465ms Wrote an address 0x14 in preparation for a bulk read/write from/to the GL841.
96 : 465ms UNKNOWN URB
97 : 466ms UNKNOWN URB
98 : 466ms [gl841:expb] -> 0x3400 Read exposure time for blue channel (13312) from the GL841.
100 : 467ms Wrote an address 0x15 in preparation for a bulk read/write from/to the GL841.
101 : 468ms UNKNOWN URB
102 : 468ms UNKNOWN URB
103 : 469ms [gl841:expb] -> 0x0004 Read exposure time for blue channel (4) from the GL841.
105 : 470ms Wrote an address 0x30 in preparation for a bulk read/write from/to the GL841.
106 : 470ms UNKNOWN URB
107 : 471ms UNKNOWN URB
108 : 471ms [gl841:strpixel] -> 0x0600 Read the beginning pixel position (1536 pixels) from the GL841.
110 : 472ms Wrote an address 0x31 in preparation for a bulk read/write from/to the GL841.
111 : 472ms UNKNOWN URB
112 : 473ms UNKNOWN URB
113 : 473ms [gl841:strpixel] -> 0x0013 Read the beginning pixel position (19 pixels) from the GL841.
115 : 474ms Wrote an address 0x32 in preparation for a bulk read/write from/to the GL841.
116 : 475ms UNKNOWN URB
117 : 475ms UNKNOWN URB
118 : 476ms [gl841:endpixel] -> 0x5500 Read the end pixel position (21760 pixels) from the GL841.
120 : 476ms Wrote an address 0x33 in preparation for a bulk read/write from/to the GL841.
121 : 477ms UNKNOWN URB
122 : 477ms UNKNOWN URB
123 : 478ms [gl841:endpixel] -> 0x0002 Read the end pixel position (2 pixels) from the GL841.
125 : 479ms Wrote an address 0x34 in preparation for a bulk read/write from/to the GL841.
126 : 479ms UNKNOWN URB
127 : 480ms UNKNOWN URB
128 : 481ms [gl841:dummy] -> 0x34 Read the dummy/optical_black pixel position (52 pixels) from the GL841.
130 : 482ms Wrote an address 0x35 in preparation for a bulk read/write from/to the GL841.
131 : 482ms UNKNOWN URB
132 : 482ms UNKNOWN URB
133 : 483ms [gl841:maxwd] -> 262144 Read Write the number of words per scanline (262144), the scanner will pause scanning if the image buffer has less than this amount of free space, from the GL841.
135 : 484ms Wrote an address 0x36 in preparation for a bulk read/write from/to the GL841.
136 : 484ms UNKNOWN URB
137 : 485ms UNKNOWN URB
138 : 485ms [gl841:maxwd] -> 45056 Read Write the number of words per scanline (45056), the scanner will pause scanning if the image buffer has less than this amount of free space, from the GL841.
140 : 486ms Wrote an address 0x37 in preparation for a bulk read/write from/to the GL841.
141 : 487ms UNKNOWN URB
142 : 487ms UNKNOWN URB
143 : 487ms [gl841:maxwd] -> 194 Read Write the number of words per scanline (194), the scanner will pause scanning if the image buffer has less than this amount of free space, from the GL841.
145 : 488ms Wrote an address 0x38 in preparation for a bulk read/write from/to the GL841.
146 : 489ms UNKNOWN URB
147 : 489ms UNKNOWN URB
148 : 490ms [gl841:lperiod] -> 0x5a00 Read line period (23040 pixels) from the GL841.
150 : 491ms Wrote an address 0x39 in preparation for a bulk read/write from/to the GL841.
151 : 491ms UNKNOWN URB
152 : 491ms UNKNOWN URB
153 : 492ms [gl841:lperiod] -> 0x00f0 Read line period (240 pixels) from the GL841.
155 : 493ms Wrote an address 0x60 in preparation for a bulk read/write from/to the GL841.
156 : 493ms UNKNOWN URB
157 : 494ms UNKNOWN URB
158 : 494ms [gl841:z1mod] -> 393216 Read slope curve table mode under buffer full moving (393216) from the GL841.
160 : 495ms Wrote an address 0x61 in preparation for a bulk read/write from/to the GL841.
161 : 496ms UNKNOWN URB
162 : 496ms UNKNOWN URB
163 : 496ms [gl841:z1mod] -> 4864 Read slope curve table mode under buffer full moving (4864) from the GL841.
165 : 497ms Wrote an address 0x62 in preparation for a bulk read/write from/to the GL841.
166 : 498ms UNKNOWN URB
167 : 498ms UNKNOWN URB
168 : 499ms [gl841:z1mod] -> 85 Read slope curve table mode under buffer full moving (85) from the GL841.
170 : 500ms Wrote an address 0x63 in preparation for a bulk read/write from/to the GL841.
171 : 501ms UNKNOWN URB
172 : 501ms UNKNOWN URB
173 : 502ms [gl841:z2mod] -> 131072 Read slope curve table mode moving to start of scan (131072) from the GL841.
175 : 502ms Wrote an address 0x64 in preparation for a bulk read/write from/to the GL841.
176 : 503ms UNKNOWN URB
177 : 503ms UNKNOWN URB
178 : 504ms [gl841:z2mod] -> 13312 Read slope curve table mode moving to start of scan (13312) from the GL841.
180 : 505ms Wrote an address 0x65 in preparation for a bulk read/write from/to the GL841.
181 : 505ms UNKNOWN URB
182 : 507ms UNKNOWN URB
183 : 507ms [gl841:z2mod] -> 4 Read slope curve table mode moving to start of scan (4) from the GL841.
185 : 514ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
186 : 514ms UNKNOWN URB
187 : 515ms UNKNOWN URB
188 : 516ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
189 : 516ms UNKNOWN URB
190 : 517ms UNKNOWN URB
191 : 518ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
192 : 518ms Setup to write 61440 bytes to endpoint 2 (bulk)
193 : 536ms UNKNOWN URB
194 : 547ms BULK WRITE ( 61440 bytes)
195 : 547ms Start/Stop Bulk Transfer (0x00)
196 : 548ms Setup to write 61440 bytes to endpoint 2 (bulk)
197 : 568ms UNKNOWN URB
198 : 619ms BULK WRITE ( 61440 bytes)
199 : 620ms Start/Stop Bulk Transfer (0x00)
200 : 622ms Setup to write 61440 bytes to endpoint 2 (bulk)
201 : 641ms UNKNOWN URB
202 : 652ms BULK WRITE ( 61440 bytes)
203 : 652ms Start/Stop Bulk Transfer (0x00)
204 : 653ms Setup to write 61440 bytes to endpoint 2 (bulk)
205 : 671ms UNKNOWN URB
206 : 681ms BULK WRITE ( 61440 bytes)
207 : 682ms Start/Stop Bulk Transfer (0x00)
208 : 682ms Setup to write 16384 bytes to endpoint 2 (bulk)
209 : 684ms UNKNOWN URB
210 : 686ms BULK WRITE ( 16384 bytes)
211 : 687ms Start/Stop Bulk Transfer (0x00)
212 : 687ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
213 : 688ms UNKNOWN URB
214 : 688ms UNKNOWN URB
215 : 689ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
216 : 689ms UNKNOWN URB
217 : 690ms UNKNOWN URB
218 : 690ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
219 : 691ms Setup to read 262146 bytes from endpoint 2 (bulk)
220 : 712ms UNKNOWN URB
222- 221: 810ms MULTIPLE BULK READS ( 65536 bytes)
222- 222: 810ms MULTIPLE BULK READS ( 65536 bytes)
223- 223: 859ms MULTIPLE BULK READS ( 65536 bytes)
224- 224: 891ms MULTIPLE BULK READS ( 65536 bytes)
225- 225: 895ms MULTIPLE BULK READS ( 2 bytes)
226 : 895ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
227 : 896ms UNKNOWN URB
228 : 896ms UNKNOWN URB
229 : 897ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
230 : 897ms UNKNOWN URB
231 : 898ms UNKNOWN URB
232 : 898ms Point to the write port of the GL841 gamma table DRAM (address 0x28) in preparation for a bulk write.
233 : 899ms Setup to write 1536 bytes to endpoint 2 (bulk)
234 : 899ms UNKNOWN URB
235 : 900ms BULK WRITE ( 1536 bytes)
236 : 900ms Start/Stop Bulk Transfer (0x00)
237 : 901ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
238 : 901ms UNKNOWN URB
239 : 901ms UNKNOWN URB
240 : 902ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
241 : 902ms UNKNOWN URB
242 : 903ms UNKNOWN URB
243 : 903ms Point to the read port of the GL841 gamma table DRAM (address 0x4e) in preparation for a bulk read.
244 : 904ms Setup to read 1538 bytes from endpoint 2 (bulk)
245 : 904ms UNKNOWN URB
247- 246: 905ms MULTIPLE BULK READS ( 1538 bytes)
247 : 905ms Wrote an address 0x66 in preparation for a bulk read/write from/to the GL841.
248 : 906ms UNKNOWN URB
249 : 906ms UNKNOWN URB
250 : 907ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
251 : 907ms UNKNOWN URB
252 : 908ms UNKNOWN URB
253 : 908ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
254 : 909ms UNKNOWN URB
255 : 910ms UNKNOWN URB
256 : 910ms Point to the write port of the GL841 gamma table DRAM (address 0x28) in preparation for a bulk write.
257 : 911ms Setup to write 128 bytes to endpoint 2 (bulk)
258 : 911ms UNKNOWN URB
259 : 911ms BULK WRITE ( 128 bytes)
260 : 912ms Start/Stop Bulk Transfer (0x00)
261 : 912ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
262 : 913ms UNKNOWN URB
263 : 913ms UNKNOWN URB
264 : 913ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
265 : 914ms UNKNOWN URB
266 : 914ms UNKNOWN URB
267 : 915ms Point to the read port of the GL841 gamma table DRAM (address 0x4e) in preparation for a bulk read.
268 : 915ms Setup to read 130 bytes from endpoint 2 (bulk)
269 : 916ms UNKNOWN URB
271- 270: 916ms MULTIPLE BULK READS ( 130 bytes)
271 : 916ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
272 : 917ms UNKNOWN URB
273 : 917ms UNKNOWN URB
274 : 918ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
275 : 918ms UNKNOWN URB
276 : 919ms UNKNOWN URB
277 : 919ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
278 : 920ms UNKNOWN URB
279 : 930ms UNKNOWN URB
280 : 930ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
281 : 931ms UNKNOWN URB
282 : 931ms UNKNOWN URB
283 : 932ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
284 : 932ms UNKNOWN URB
285 : 933ms UNKNOWN URB
286 : 933ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
287 : 934ms UNKNOWN URB
288 : 944ms UNKNOWN URB
289 : 944ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
290 : 945ms UNKNOWN URB
291 : 945ms UNKNOWN URB
292 : 946ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
293 : 946ms UNKNOWN URB
294 : 947ms UNKNOWN URB
295 : 947ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
296 : 948ms UNKNOWN URB
297 : 1008ms UNKNOWN URB
298- 299: 1009ms [gl841:scanner_status] -> 0xf8 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
*scanner is position: home
scanning is : finished
*motor feeding : finished
image buffer is : empty
*power : on
300- 301: 1010ms [gl841:scanner_status] -> 0xf8 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: home
scanning is : finished
motor feeding : finished
image buffer is : empty
power : on
302- 303: 1060ms [gl841:scanner_status] -> 0xf8 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: home
scanning is : finished
motor feeding : finished
image buffer is : empty
power : on
304- 305: 1061ms [gl841:scanner_status] -> 0xf8 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: home
scanning is : finished
motor feeding : finished
image buffer is : empty
power : on
306 : 1071ms Wrote an address 0x66 in preparation for a bulk read/write from/to the GL841.
307 : 1071ms UNKNOWN URB
308 : 1072ms UNKNOWN URB
309 : 1072ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
310 : 1073ms UNKNOWN URB
311 : 1073ms UNKNOWN URB
312 : 1074ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
313 : 1074ms UNKNOWN URB
314 : 1074ms UNKNOWN URB
315 : 1075ms Point to the write port of the GL841 gamma table DRAM (address 0x28) in preparation for a bulk write.
316 : 1075ms Setup to write 128 bytes to endpoint 2 (bulk)
317 : 1076ms UNKNOWN URB
318 : 1076ms BULK WRITE ( 128 bytes)
319 : 1076ms Start/Stop Bulk Transfer (0x00)
320 : 1077ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
321 : 1078ms UNKNOWN URB
322 : 1078ms UNKNOWN URB
323 : 1079ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
324 : 1079ms UNKNOWN URB
325 : 1079ms UNKNOWN URB
326 : 1080ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
327 : 1080ms UNKNOWN URB
328 : 1081ms UNKNOWN URB
329 : 1081ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
330 : 1082ms UNKNOWN URB
331 : 1082ms UNKNOWN URB
332 : 1083ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
333 : 1083ms Setup to write 256 bytes to endpoint 2 (bulk)
334 : 1084ms UNKNOWN URB
335 : 1084ms BULK WRITE ( 256 bytes)
336 : 1084ms Start/Stop Bulk Transfer (0x00)
337 : 1085ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
338 : 1085ms UNKNOWN URB
339 : 1086ms UNKNOWN URB
340 : 1086ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
341 : 1087ms UNKNOWN URB
342 : 1087ms UNKNOWN URB
343 : 1087ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
344 : 1088ms Setup to write 256 bytes to endpoint 2 (bulk)
345 : 1088ms UNKNOWN URB
346 : 1089ms BULK WRITE ( 256 bytes)
347 : 1108ms Start/Stop Bulk Transfer (0x00)
348 : 1109ms UNKNOWN URB
349 : 1110ms UNKNOWN URB
350 : 1111ms UNKNOWN URB
351 : 1132ms UNKNOWN URB
352 : 1132ms Wrote an address 0x0f in preparation for a bulk read/write from/to the GL841.
353 : 1132ms UNKNOWN URB
354 : 1183ms UNKNOWN URB
355- 362: 1183ms Wait for motor to stop processing. ([0x41] bit 0)==1
363 : 1355ms UNKNOWN URB
364 : 1356ms UNKNOWN URB
365 : 1357ms UNKNOWN URB
366 : 1428ms UNKNOWN URB
367- 368: 1428ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
369 : 1438ms Wrote an address 0x66 in preparation for a bulk read/write from/to the GL841.
370 : 1439ms UNKNOWN URB
371 : 1439ms UNKNOWN URB
372 : 1439ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
373 : 1440ms UNKNOWN URB
374 : 1440ms UNKNOWN URB
375 : 1441ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
376 : 1441ms UNKNOWN URB
377 : 1442ms UNKNOWN URB
378 : 1442ms Point to the write port of the GL841 gamma table DRAM (address 0x28) in preparation for a bulk write.
379 : 1443ms Setup to write 128 bytes to endpoint 2 (bulk)
380 : 1443ms UNKNOWN URB
381 : 1443ms BULK WRITE ( 128 bytes)
382 : 1444ms Start/Stop Bulk Transfer (0x00)
383 : 1444ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
384 : 1445ms UNKNOWN URB
385 : 1445ms UNKNOWN URB
386 : 1446ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
387 : 1446ms UNKNOWN URB
388 : 1446ms UNKNOWN URB
389 : 1447ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
390 : 1447ms UNKNOWN URB
391 : 1448ms UNKNOWN URB
392 : 1448ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
393 : 1449ms UNKNOWN URB
394 : 1449ms UNKNOWN URB
395 : 1450ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
396 : 1450ms Setup to write 256 bytes to endpoint 2 (bulk)
397 : 1451ms UNKNOWN URB
398 : 1451ms BULK WRITE ( 256 bytes)
399 : 1451ms Start/Stop Bulk Transfer (0x00)
400 : 1452ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
401 : 1452ms UNKNOWN URB
402 : 1453ms UNKNOWN URB
403 : 1453ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
404 : 1454ms UNKNOWN URB
405 : 1454ms UNKNOWN URB
406 : 1455ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
407 : 1455ms Setup to write 256 bytes to endpoint 2 (bulk)
408 : 1455ms UNKNOWN URB
409 : 1456ms BULK WRITE ( 256 bytes)
410 : 1476ms Start/Stop Bulk Transfer (0x00)
411 : 1477ms UNKNOWN URB
412 : 1477ms UNKNOWN URB
413 : 1478ms UNKNOWN URB
414 : 1499ms UNKNOWN URB
415 : 1499ms Wrote an address 0x0f in preparation for a bulk read/write from/to the GL841.
416 : 1500ms UNKNOWN URB
417 : 1520ms UNKNOWN URB
418- 439: 1520ms Wait for motor to stop processing. ([0x41] bit 0)==1
440 : 1856ms UNKNOWN URB
441 : 1857ms UNKNOWN URB
442 : 1858ms UNKNOWN URB
443 : 1878ms UNKNOWN URB
444 : 1879ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
445 : 1879ms UNKNOWN URB
446 : 1879ms UNKNOWN URB
447 : 1880ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
448 : 1880ms UNKNOWN URB
449 : 1881ms UNKNOWN URB
450 : 1881ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
451 : 1882ms Setup to write 16 bytes to endpoint 2 (bulk)
452 : 1882ms UNKNOWN URB
453 : 1883ms BULK WRITE ( 16 bytes)
454 : 1883ms Start/Stop Bulk Transfer (0x00)
455 : 1883ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
456 : 1884ms UNKNOWN URB
457 : 1884ms UNKNOWN URB
458 : 1885ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
459 : 1885ms UNKNOWN URB
460 : 1886ms UNKNOWN URB
461 : 1886ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
462 : 1887ms Setup to write 16 bytes to endpoint 2 (bulk)
463 : 1887ms UNKNOWN URB
464 : 1887ms BULK WRITE ( 16 bytes)
465 : 1888ms Start/Stop Bulk Transfer (0x00)
466 : 1888ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
467 : 1889ms UNKNOWN URB
468 : 1889ms UNKNOWN URB
469 : 1890ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
470 : 1890ms UNKNOWN URB
471 : 1890ms UNKNOWN URB
472 : 1891ms Point to the write port of the GL841 image buffer DRAM (address 0x3c) in preparation for a bulk write.
473 : 1891ms Setup to write 16 bytes to endpoint 2 (bulk)
474 : 1892ms UNKNOWN URB
475 : 1892ms BULK WRITE ( 16 bytes)
476 : 1892ms Start/Stop Bulk Transfer (0x00)
477 : 1893ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
478 : 1893ms UNKNOWN URB
479 : 1894ms UNKNOWN URB
480 : 1894ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
481 : 1895ms UNKNOWN URB
482 : 1895ms UNKNOWN URB
483 : 1896ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
484 : 1896ms UNKNOWN URB
485 : 1906ms UNKNOWN URB
486 : 1907ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
487 : 1907ms UNKNOWN URB
488 : 1907ms UNKNOWN URB
489 : 1908ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
490 : 1908ms UNKNOWN URB
491 : 1909ms UNKNOWN URB
492 : 1909ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
493 : 1910ms UNKNOWN URB
494 : 1940ms UNKNOWN URB
495 : 1941ms UNKNOWN URB
496 : 1942ms UNKNOWN URB
497 : 1943ms UNKNOWN URB
498 : 1964ms UNKNOWN URB
499 : 1964ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
500 : 1965ms UNKNOWN URB
501 : 1965ms UNKNOWN URB
502 : 1966ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
503 : 1966ms UNKNOWN URB
504 : 1966ms UNKNOWN URB
505 : 1967ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
506 : 1967ms UNKNOWN URB
507 : 1977ms UNKNOWN URB
508 : 1978ms Wrote an address 0x0d in preparation for a bulk read/write from/to the GL841.
509 : 1978ms UNKNOWN URB
510 : 1979ms UNKNOWN URB
511- 512: 1979ms [gl841:motor_gpio17_18] -> 0x03 Read Set motor pins and GPIO17-18.
*GPO17 : 1
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
513 : 1980ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
514 : 1981ms UNKNOWN URB
515 : 2011ms UNKNOWN URB
516 : 2042ms UNKNOWN URB
517- 522: 2042ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
523- 528: 2054ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
529- 534: 2066ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
535- 540: 2078ms [gl841:validword] -> 88 Read number of bytes available to read from the image buffer (88) from the GL841.
541 : 2081ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
542 : 2081ms Setup to read 7656 bytes from endpoint 2 (bulk)
543 : 2082ms UNKNOWN URB
545- 544: 2133ms MULTIPLE BULK READS ( 7656 bytes)
545 : 2133ms 0x02 -> [gl841:scanner_setup] Write scanner setup.
scan process : disable
*shading area : enable
DRAM size : 4Mx1
DRAM size : 4M or 8M
shading : disable
watchdog timer (register 0x1e): disable
scanner type : CCD
546 : 2133ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
547 : 2134ms UNKNOWN URB
548 : 2134ms UNKNOWN URB
549 : 2135ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
550 : 2135ms UNKNOWN URB
551 : 2136ms UNKNOWN URB
552 : 2136ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
553 : 2137ms UNKNOWN URB
554 : 2147ms UNKNOWN URB
555- 556: 2147ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
*GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
557 : 2148ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
558 : 2149ms UNKNOWN URB
559 : 2209ms UNKNOWN URB
560- 561: 2210ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
*motor feeding : not finished
image buffer is : empty
power : on
562 : 2231ms UNKNOWN URB
563 : 2232ms UNKNOWN URB
564 : 2233ms UNKNOWN URB
565 : 2253ms UNKNOWN URB
566 : 2254ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
567 : 2254ms UNKNOWN URB
568 : 2255ms UNKNOWN URB
569 : 2255ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
570 : 2256ms UNKNOWN URB
571 : 2256ms UNKNOWN URB
572 : 2257ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
573 : 2257ms UNKNOWN URB
574 : 2267ms UNKNOWN URB
575 : 2268ms Wrote an address 0x0d in preparation for a bulk read/write from/to the GL841.
576 : 2268ms UNKNOWN URB
577 : 2269ms UNKNOWN URB
578- 579: 2269ms [gl841:motor_gpio17_18] -> 0x03 Read Set motor pins and GPIO17-18.
*GPO17 : 1
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
580 : 2270ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
581 : 2271ms UNKNOWN URB
582 : 2300ms UNKNOWN URB
583 : 2331ms UNKNOWN URB
584- 589: 2331ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
590- 595: 2343ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
596- 601: 2355ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
602- 607: 2367ms [gl841:validword] -> 273 Read number of bytes available to read from the image buffer (273) from the GL841.
608 : 2370ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
609 : 2371ms Setup to read 7656 bytes from endpoint 2 (bulk)
610 : 2371ms UNKNOWN URB
612- 611: 2411ms MULTIPLE BULK READS ( 7656 bytes)
612 : 2411ms 0x02 -> [gl841:scanner_setup] Write scanner setup.
scan process : disable
shading area : enable
DRAM size : 4Mx1
DRAM size : 4M or 8M
shading : disable
watchdog timer (register 0x1e): disable
scanner type : CCD
613 : 2411ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
614 : 2412ms UNKNOWN URB
615 : 2412ms UNKNOWN URB
616 : 2413ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
617 : 2413ms UNKNOWN URB
618 : 2414ms UNKNOWN URB
619 : 2414ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
620 : 2415ms UNKNOWN URB
621 : 2425ms UNKNOWN URB
622- 623: 2425ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
*GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
624 : 2426ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
625 : 2427ms UNKNOWN URB
626 : 2487ms UNKNOWN URB
627- 628: 2488ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
629 : 2509ms UNKNOWN URB
630 : 2510ms UNKNOWN URB
631 : 2511ms UNKNOWN URB
632 : 2587ms UNKNOWN URB
633 : 2587ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
634 : 2588ms UNKNOWN URB
635 : 2589ms UNKNOWN URB
636 : 2591ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
637 : 2591ms UNKNOWN URB
638 : 2592ms UNKNOWN URB
639 : 2592ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
640 : 2593ms UNKNOWN URB
641 : 2602ms UNKNOWN URB
642 : 2603ms Wrote an address 0x0d in preparation for a bulk read/write from/to the GL841.
643 : 2603ms UNKNOWN URB
644 : 2604ms UNKNOWN URB
645- 646: 2604ms [gl841:motor_gpio17_18] -> 0x03 Read Set motor pins and GPIO17-18.
*GPO17 : 1
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
647 : 2605ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
648 : 2606ms UNKNOWN URB
649 : 2636ms UNKNOWN URB
650 : 2666ms UNKNOWN URB
651- 656: 2666ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
657- 662: 2678ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
663- 668: 2690ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
669- 674: 2703ms [gl841:validword] -> 42 Read number of bytes available to read from the image buffer (42) from the GL841.
675 : 2705ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
676 : 2706ms Setup to read 7656 bytes from endpoint 2 (bulk)
677 : 2706ms UNKNOWN URB
679- 678: 2757ms MULTIPLE BULK READS ( 7656 bytes)
679 : 2757ms 0x02 -> [gl841:scanner_setup] Write scanner setup.
scan process : disable
shading area : enable
DRAM size : 4Mx1
DRAM size : 4M or 8M
shading : disable
watchdog timer (register 0x1e): disable
scanner type : CCD
680 : 2758ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
681 : 2758ms UNKNOWN URB
682 : 2758ms UNKNOWN URB
683 : 2759ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
684 : 2759ms UNKNOWN URB
685 : 2760ms UNKNOWN URB
686 : 2760ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
687 : 2761ms UNKNOWN URB
688 : 2771ms UNKNOWN URB
689- 690: 2772ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
*GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
691 : 2772ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
692 : 2773ms UNKNOWN URB
693 : 2833ms UNKNOWN URB
694- 695: 2834ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
696 : 2855ms UNKNOWN URB
697 : 2856ms UNKNOWN URB
698 : 2857ms UNKNOWN URB
699 : 2877ms UNKNOWN URB
700 : 2878ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
701 : 2878ms UNKNOWN URB
702 : 2879ms UNKNOWN URB
703 : 2879ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
704 : 2880ms UNKNOWN URB
705 : 2880ms UNKNOWN URB
706 : 2881ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
707 : 2881ms UNKNOWN URB
708 : 2891ms UNKNOWN URB
709 : 2892ms Wrote an address 0x0d in preparation for a bulk read/write from/to the GL841.
710 : 2892ms UNKNOWN URB
711 : 2893ms UNKNOWN URB
712- 713: 2893ms [gl841:motor_gpio17_18] -> 0x03 Read Set motor pins and GPIO17-18.
*GPO17 : 1
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
714 : 2894ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
715 : 2895ms UNKNOWN URB
716 : 2924ms UNKNOWN URB
717 : 2955ms UNKNOWN URB
718- 723: 2955ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
724- 729: 2967ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
730- 735: 2979ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
736- 741: 2991ms [gl841:validword] -> 87 Read number of bytes available to read from the image buffer (87) from the GL841.
742 : 2994ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
743 : 2994ms Setup to read 7656 bytes from endpoint 2 (bulk)
744 : 2995ms UNKNOWN URB
746- 745: 3045ms MULTIPLE BULK READS ( 7656 bytes)
746 : 3045ms 0x02 -> [gl841:scanner_setup] Write scanner setup.
scan process : disable
shading area : enable
DRAM size : 4Mx1
DRAM size : 4M or 8M
shading : disable
watchdog timer (register 0x1e): disable
scanner type : CCD
747 : 3045ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
748 : 3046ms UNKNOWN URB
749 : 3046ms UNKNOWN URB
750 : 3047ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
751 : 3047ms UNKNOWN URB
752 : 3048ms UNKNOWN URB
753 : 3048ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
754 : 3049ms UNKNOWN URB
755 : 3059ms UNKNOWN URB
756- 757: 3059ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
*GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
758 : 3060ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
759 : 3061ms UNKNOWN URB
760 : 3121ms UNKNOWN URB
761- 762: 3122ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
763 : 3143ms UNKNOWN URB
764 : 3144ms UNKNOWN URB
765 : 3145ms UNKNOWN URB
766 : 3165ms UNKNOWN URB
767 : 3166ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
768 : 3166ms UNKNOWN URB
769 : 3167ms UNKNOWN URB
770 : 3167ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
771 : 3168ms UNKNOWN URB
772 : 3168ms UNKNOWN URB
773 : 3169ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
774 : 3169ms UNKNOWN URB
775 : 3179ms UNKNOWN URB
776 : 3180ms Wrote an address 0x0d in preparation for a bulk read/write from/to the GL841.
777 : 3180ms UNKNOWN URB
778 : 3181ms UNKNOWN URB
779- 780: 3181ms [gl841:motor_gpio17_18] -> 0x03 Read Set motor pins and GPIO17-18.
*GPO17 : 1
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
781 : 3182ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
782 : 3183ms UNKNOWN URB
783 : 3213ms UNKNOWN URB
784 : 3243ms UNKNOWN URB
785- 790: 3244ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
791- 796: 3256ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
797- 802: 3268ms [gl841:validword] -> 0 Read number of bytes available to read from the image buffer (0) from the GL841.
803- 808: 3280ms [gl841:validword] -> 1014 Read number of bytes available to read from the image buffer (1014) from the GL841.
809 : 3283ms Point to the read port of the GL841 image buffer DRAM (address 0x45) in preparation for a bulk read.
810 : 3283ms Setup to read 7656 bytes from endpoint 2 (bulk)
811 : 3284ms UNKNOWN URB
813- 812: 3333ms MULTIPLE BULK READS ( 7656 bytes)
813 : 3333ms 0x02 -> [gl841:scanner_setup] Write scanner setup.
scan process : disable
shading area : enable
DRAM size : 4Mx1
DRAM size : 4M or 8M
shading : disable
watchdog timer (register 0x1e): disable
scanner type : CCD
814 : 3334ms Wrote an address 0x51 in preparation for a bulk read/write from/to the GL841.
815 : 3334ms UNKNOWN URB
816 : 3334ms UNKNOWN URB
817 : 3335ms Wrote an address 0x3a in preparation for a bulk read/write from/to the GL841.
818 : 3335ms UNKNOWN URB
819 : 3336ms UNKNOWN URB
820 : 3336ms Wrote an address 0x3b in preparation for a bulk read/write from/to the GL841.
821 : 3337ms UNKNOWN URB
822 : 3347ms UNKNOWN URB
823- 824: 3347ms [gl841:motor_gpio17_18] -> 0x02 Read Set motor pins and GPIO17-18.
*GPO17 : 0
GPO18 : 1
GPOM11 : select as GPIO11
GPOM12 : select as GPIO12
GPOM13 : select as GPIO13
Multifilm: motor phase normal
825 : 3348ms Wrote an address 0x6b in preparation for a bulk read/write from/to the GL841.
826 : 3349ms UNKNOWN URB
827 : 3409ms UNKNOWN URB
828- 829: 3410ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
830- 831: 3461ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
832- 833: 3462ms [gl841:scanner_status] -> 0xd0 Read scanner status.
motor is : not processing
front end is : not busy (ready to read/write)
lamp is : off
scanner is position: not home
scanning is : finished
motor feeding : not finished
image buffer is : empty
power : on
834 : 3472ms Wrote an address 0x66 in preparation for a bulk read/write from/to the GL841.
835 : 3472ms UNKNOWN URB
836 : 3473ms UNKNOWN URB
837 : 3473ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
838 : 3474ms UNKNOWN URB
839 : 3474ms UNKNOWN URB
840 : 3475ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
841 : 3475ms UNKNOWN URB
842 : 3475ms UNKNOWN URB
843 : 3476ms Point to the write port of the GL841 gamma table DRAM (address 0x28) in preparation for a bulk write.
844 : 3476ms Setup to write 128 bytes to endpoint 2 (bulk)
845 : 3477ms UNKNOWN URB
846 : 3477ms BULK WRITE ( 128 bytes)
847 : 3477ms Start/Stop Bulk Transfer (0x00)
848 : 3478ms Wrote an address 0x5b in preparation for a bulk read/write from/to the GL841.
849 : 3478ms UNKNOWN URB
850 : 3479ms UNKNOWN URB
851 : 3479ms Wrote an address 0x5c in preparation for a bulk read/write from/to the GL841.
852 : 3480ms UNKNOWN URB
853 : 3480ms UNKNOWN URB
854 : 3481ms Wrote an address 0x2a in preparation for a bulk read/write from/to the GL841.
855 : 3481ms UNKNOWN URB
856 : 3482ms UNKNOWN URB
857 : 3482ms Wrote an address 0x2b in preparation for a bulk read/write from/to the GL841.
858 :